QLICK rail
The QLICK aluminium substructure with pre-installed fixing clips for boards with a groove on the underside ensures a harmonious joint pattern. There are three versions of the QLICK aluminium substructure: for boards with widths 120 mm, 140 mm and 155 mm. The boards are attached by laying them down and clicking them into position from above. This special click-in technique also enables a rapid removal and re-laying of the boards. The high structural strength of the rail ensures a span of 950 mm (2kN), 750 mm (4kN) or 650 mm (5kN for commercial purposes). The QLICK Alu-UK is suitable for installation heights from 53 mm. Separate rails and fasteners are also available for laying on slopes. These can be fitted on site to suit the surface.
Advantages:
- for installation heights from 53 mm
- High statics for fewer support points (4 kN/750 mm)
- Pre-assembled fasteners save one work step
- Compatible with the K&R system such as connectors, terrace bearings or Isopad
Assembly video
Technical data:
Product | Item no. | Dimension | Quantity of planks | Quantity / PU | PU / pallet |
|---|---|---|---|---|---|
QLICK alu rail 120 | 9675 | 68x41x3968mm | 32 | 1 pc. | 64 |
9676 | 68x41x1984mm | 16 | 1 pc. | 64 | |
QLICK alu rail 140 | 9679 | 68x41x3915mm | 27 | 1 pc. | 64 |
9680 | 68x41x1885mm | 13 | 1 pc. | 64 | |
QLICK alu rail 155 | 9122 | 68x41x1932mm | 12 | 1 pc. | 64 |
9123 | 68x41x3964mm | 24 | 1 pc. | 64 |
Everything in the system
Connector for CLIP rails
Without affecting the statics, the substructure can be extended endlessly by simply inserting it into the rail to optimize waste. The corner connectors are ideal for a substructure frame if it is not possible to fix the substructure to the floor on site. There is a suitable connector for every CLIP rail.
Advantages:
-
Waste-optimized assembly of the substructure
-
Maintaining the full rail statics
Technical data:
Product | Item no. | Dimension | Quantity / PU | PU / carton |
|---|---|---|---|---|
Connector BIG-/TWIXT-Isostep | 6961 | 18x59x196 mm | 4 pcs. | 8 |
CLIP decking support feet
With the special CLIP top, all Isostep CLIP rails can be connected to the decking support quickly and without screws by simply clicking them on. With this combination, the CLIP components achieve a simple and even faster assembly of the entire substructure.
Advantages:
-
Quick assembly of the substructure in conjunction with the Isostep CLIP rails
-
The patented attachment, which can be moved in all directions, compensates for slopes of up to 8% in the substrate
-
The double thread enables stepless and millimeter-precise height adjustment by simply turning to the right/left
-
In the CLIP system, the substructure can be installed almost without screws by simply clicking it on
-
All components of the adjustable feet are connected to each other and locked toprevent unintentional unscrewing
-
All terrace bearings are produced in Germany
-
TERRACON® bearings have proven themselves in practice for years.lasts. It is a high-quality product series for the professional user.safe and time-saving construction of a terrace.
Adjustment ranges:
Isopad / Loftis
The special vapour-permeable rubber granulate pads ensure a long service life of the deck flooring. By selectively underlying the substructure, direct contact to the substrate is prevented, which allows water to run off unimpeded and also attenuates the impact sound of footsteps. Also perfectly suited to level out surface irregularities. With the Loftis roll, the rubber granulate is also available in a length of 2300 mm.
Advantages:
- Prevention of waterlogging
- Levels out minor surface irregularities
- Wood protection towards the top, structural protection towards the bottom
- guarantees wood protection at the top and building protection at the bottom
- Dampens footstep sounds on the deck flooring
- Rot-proof materials
- non-slip